Honeywell ® Reset - Önyükleme

Honeywell ® Soft - Hard - Factory Reset
Honeywell Dolphin 5100 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 5100 Soft Reset - Warm Boot

1. Press the Reset button. The screen turns white and the decode and scan LED flashes blue for approximately 3 seconds.
2. When the reset is complete, the Desktop appears.


Dolphin 5100 Hard Reset - Cold Boot

1. Press and hold the Reset button and then press and release the Power button.
   The screen turns white and the decode and scan LED flashes red for approximately 3 seconds.
2. The terminal re-initializes, which re-installs all programs stored in \Honeywell\Autoinstall folder.


Honeywell Dolphin 60S Soft - Hard - Factory Reset (Warm - Cold Boot)

Dolphin 60S Soft Reset - Warm Boot

1. Press and hold the Blue key and then Power key for approximately 6-7 seconds.
2. When the reset is complete, the Home screen displays


Dolphin 60S Hard Reset - Cold Boot

1. Press and hold the Blue key and then Green Call key for approximately 6-7 seconds.
2. When the reset is complete, the Home screen displays.

Dolphin 60S Factory Reset

1. Press and hold the Blue button and Green Call button to cold boot the Dolphin.
2. Upon cold boot, when the display returns, type: 1277.
3. A little menu will appear showing the reset options. Choose the top option by pressing the number < 1 > on the keypad.
4. A prompt will appear asking for confirmation. Press the ENTER key on the keypad to proceed or the ESC key to cancel.

Honeywell Dolphin 6000 Soft - Hard - Factory Reset (Warm - Cold Boot)

Dolphin 6000 Soft Reset - Warm Boot

1. Tap Start > Power Tools > Reboot > Reboot.
2. This will restart the device.


Dolphin 6000 Hard Reset - Cold Boot

1. Press and hold the Power button for 3 seconds.
2. Select OK on the popup to shutdown the device.
3. Press and hold the Power button again to reboot the device.


Dolphin 6000 Factory Reset

1. Press the Power button for 3 seconds.
2. Select “OK” on the question: "This may cause information loss do you really want to shutdown?"
3. Press and keep pressing the VOLUME-UP and UP keys.
4. Press the Power button until a menu appears which will show the Clean Boot option.
5. Select DOWN on the question "Press DOWN to restore manufacturer default" to perform a factory reset.


Honeywell Dolphin 6100 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 6100 Soft Reset - Warm Boot

1. Press the Reset button. The screen turns white and the decode and scan LED flashes blue for approximately 3 seconds.
2. When the reset is complete, the Desktop appears.


Dolphin 6100 Hard Reset - Cold Boot

1. Press and hold the Reset button and then press and release the Power button.
   The screen turns white and the decode and scan LED flashes red for approximately 3 seconds.
2. The terminal re-initializes, which re-installs all programs stored in \Honeywell\Autoinstall folder.


Honeywell Dolphin 6110 Soft - Hard - Factory Reset (Warm - Cold Boot)

Dolphin 6110 Soft Reset - Warm Boot

1. Press and hold the Power button until the options menu appears.
2. Tap Soft Reset on the menu.
3. When the reset is complete, the Home screen displays.


Dolphin 6110 Hard Reset - Cold Boot

1. Press and hold the Power button until the options menu appears.
2. Tap Hard Reset on the menu.
3. When the reset is complete, the Home screen displays.

Note: If the screen has stopped responding, press and hold the Power button
            for approximately 8 seconds until the terminal starts to re-boot.

Dolphin 6110 Factory Reset

1. Press the Power key for 5 seconds.
2. Select Hard Reset in the menu that appears.
3. When the white boot screen appears and the LED blinks, type the following keys in sequence:
   "1", "2", "7", "7". This will be displayed in a small box in the center of the screen.
4. The device will show a menu with 2 options. When the menu appears,
   press the ENT(Enter) key to select the Factory Reset option.
5. Select the ENT (Enter) key on the question to proceed. At this moment,
   the device will start the "Factory Mode" process.


Honeywell Dolphin 6500 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 6500 Soft Reset - Warm Boot

1.Using the stylus, press the Reset button. The screen turns white and
  the decode/scan LED flashes blue for approximately 10 seconds.


Dolphin 6500 Hard Reset - Cold Boot

1. On the 28-key keyboard, press and hold the Power button and then using the stylus, press Reset button.
   On the 52-key keyboard, press and hold the Blue and Z (Power) button and then using the stylus, press Reset button.
2. The screen turns white and the decode/scan LED flashes blue for approximately 18 seconds.


Honeywell Dolphin 7600 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 7600 Soft Reset - Warm Boot

1. Press and hold Red button and ESC button for approximately 5 seconds.
   The screen turns white and the decode and scan LEDs flash for approximately 3 seconds.
2. When the reset is complete, the Desktop appears.


Dolphin 7600 Hard Reset - Cold Boot

1. Press and hold Red button and TAB button for approximately 5 seconds.
   The screen turns white and the decode and scan LEDs flash for approximately 3 seconds.
2. The terminal re-initializes, which re-installs all programs stored in the \IPSM\Autoinstall folder.

Honeywell Dolphin 70e Black Hard - Factory Reset (Cold Boot)

Dolphin 70e Black Hard Reset - Cold Boot

1. Press and hold the Power button until the Phone Options menu displays.
2. Touch Reboot.

Dolphin 70e Black Factory Reset

To Factory Default the 70E terminal running Windows Embedded Handheld:

1. Perform a Hard reset. Press and hold the Power button on the top of the device
   until the display gives power down options. Tap Hard Reset.
2. While the Dolphin is booting, press and hold the left and right scan keys
   until the Honeywell splash screen comes up with the Factory Reset box.
  
   Note: Factory reset box is only visible for 3 seconds.
  
3. Once the white Honeywell splash screen appears and the Factory Reset box is in the center of the screen,
   press the Green Phone key, then the Red Disconnect key, then the Home key.
4. As a last confirmation, press the front SCAN button, and the Factory Reset will be initiated.

To Factory Default the 70E terminal running Android:

1. Perform a Reboot. Press and hold the Power button on the top of the device
   until the display gives power down options. Tap Reboot.
2. While the Dolphin is booting, press and hold the left and right scan keys until
   the Honeywell splash screen comes up with a “Ready for hotkey” message at the bottom of the screen.
3. Once the white Honeywell splash screen appears and the “Ready for hotkey”
   message is in the bottom left corner of the screen, press the Search key
   and then the Volume Down button, and this will start the factory reset process.
  
   Note: These keys are pressed in sequence as they constitute the password to perform the Factory reset.

Honeywell Dolphin 7850 / 7900 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 7850 / 7900 Soft Reset - Warm Boot

1. Press and hold the Red button and ESC button or approximately 5 seconds.
2. The decode and scan LEDs flash for approximately three seconds as the terminal resets.
3. When the reset is complete, the Today screen displays.


Dolphin 7850 / 7900 Hard Reset - Cold Boot

1. Press and hold the Red button and TAB button for approximately 5 seconds.
2. The decode and scan LEDs flash for approximately 3  seconds as the terminal resets.
3. The terminal re-initializes.

Honeywell Dolphin 7800 Soft - Hard - Factory Reset (Warm - Cold Boot)

Dolphin 7800 Soft Reset - Warm Boot

1. Press and hold the Blue button and Red Disconnect button for approximately 5 seconds.
2. The general notification LED flashes orange then green for approximately 3 seconds as the terminal resets.
3. When the reset is complete, the Home screen displays.


Dolphin 7800 Hard Reset - Cold Boot

1. Press and hold the Blue button and Green Call button for approximately 5 seconds.
2. The general notification LED flashes orange then green for approximately 3 seconds as the terminal resets.
3. The terminal re-initializes.


Dolphin 7800 Factory Reset

1. Press and hold the Blue button and Green Call button to cold boot the Dolphin.
2. Upon cold boot, when the display returns, type: 1277.
3. A little menu will appear showing the reset options. Choose the top option by pressing the number < 1 > on the keypad.
4. A prompt will appear asking for confirmation. Press the ENTER key on the keypad to proceed or the ESC key to cancel.


Honeywell Dolphin 9700 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 9700 Soft Reset - Warm Boot

1. Press and hold the Red button and TAB button for approximately 5 seconds.
2. The decode and scan LEDs flash for approximately 3 seconds as the terminal resets.
3. When the reset is complete, the Today screen displays.


Dolphin 9700 Hard Reset - Cold Boot

1. Press and hold the Red button and ENT button for approximately 5 seconds.
2. The decode and scan LEDs light for approximately 3 seconds.
3. The terminal re-initializes.

Honeywell Dolphin 9500 / 9550 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 9500 / 9550 Soft Reset - Warm Boot

1. Press and hold the Control (CTRL) and the SHIFT (SFT) keys for approximately 10 seconds, then release.
2. Release the keys and the terminal resets.
   The red LED comes on and the green LED blinks for approximately 3 seconds.
3. The terminal will initialize and after a few seconds will display the Today screen.


Dolphin 9500 / 9550 Hard Reset - Cold Boot

1. Press and hold the Control (CTRL) and the Escape (ESC) keys for approximately 10 seconds.
2. Release the keys and the terminal resets.
   The red LED comes on and the green LED blinks for approximately 3 seconds.
3. When you turn on the terminal again, it will need to be reconfigured.

Honeywell Dolphin 99EX / 99GX Soft - Hard - Factory Reset (Warm - Cold Boot)

Dolphin 99EX / 99GX Soft Reset - Warm Boot

1. Press and hold the CTRL + ENT keys for approximately 5 seconds.
2. The decode and scan LEDs flash for approximately three seconds as the terminal Resets.
3. When the reset is complete, the Home screen displays.


Dolphin 99EX / 99GX Hard Reset - Cold Boot

1. Press and hold the CTRL + ESC keys for approximately 5 seconds.
2. The decode and scan LEDs light for approximately 3 seconds.
3. The terminal re-initializes.

Dolphin 99EX / 99GX Factory Reset

1. Press and hold the CTRL + ESC keys simultaneously for approximate 5 seconds.
   You may hear a clicking sound when you hold the keys down.
2. When the white Honeywell splash screen appears, enter code 1277 on the keyboard.
   For terminals with a 34-key Numeric (Calculator) Keyboard, enter code 7811 instead of 1277.
3. Select Perform Factory Reset from the menu, and then press ENT.
   The following message appears on the terminal screen:
   “All installed applications & customized settings will be deleted. Do you want to proceed?”
4. Press Y for yes, proceed with the Factory Reset. If you change your mind and do not want to proceed,
   press N for no and the terminal will launch the current image instead of a factory reset.


Honeywell Dolphin 9900 / 9950 Soft - Hard Reset (Warm - Cold Boot)

Dolphin 9900 / 9950 Soft Reset - Warm Boot

1. On the 56-key keyboard, press and hold the CTRL + SFT keys for approximately 5 seconds.
   On the 43-key keyboard, press and hold the CTRL + NUM keys for approximately 5 seconds.
2. The decode and scan LEDs flash for approximately 3 seconds as the terminal resets.
3. When the reset is complete, the Today screen displays.


Dolphin 9900 / 9950 Hard Reset - Cold Boot

1. Press and hold the CTRL + ESC keys for approximately 5 seconds.
2. The decode and scan LEDs light for approximately 3 seconds.
3. The terminal re-initializes.

Honeywell IT3800-LR / 4600G-SR / IT5800-SR Factory Reset

IT3800-LR / 4600G-SR / IT5800-SR Factory Reset

1. The following bar code resets all factory defaults:




Honeywell 8600 / 8620 / 8650 Ring Scanner Factory Reset

8600 / 8620 / 8650 Ring Scanner Factory Reset

1. Scanning the following bar code to return all parameters to their default values:




    Scanning the following bar code to cancel:




Honeywell MS5145 Factory Reset

MS5145 Factory Reset

1. Scan the following barcode by recall Defaults code to enable and load Factory Defaults: